GMC Sierra 1500 Transmission Problems & Cost | 4L60E | 6L80 | 8L90

The GMC Sierra 1500 was equipped with the 4L60E in early models, and 6-speed 6L80 in later models and 8-speed 8L90 in 2015+ models. But they aren’t without their problems though, so let’s look at some of the most common GMC Sierra 1500 transmission problems, look at cost estimates and figure out what you can do about them.

Need a replacement transmission? Get an estimate for replacement transmissions and local installation. Look up your transmission model by vehicle make and model.

What Transmission Do I Have?

GMC Sierra 1500 Transmission Models

GMC Sierra 1500: 4L60E Transmission
GMC Sierra 1500: 4L65E Transmission
GMC Sierra 1500: 4L80E Transmission
GMC Sierra 1500: 6L80 Transmission
GMC Sierra 1500: 8L90 Transmission (2015+)

GMC Sierra 1500 Transmission Replacement Cost Estimate

Pricing varies by model. To be 100% sure on pricing, have your VIN# handy and use our Get An Estimate feature to look up your transmission by VIN#.

Replacement GMC Sierra 1500 Transmission Prices:

TransmissionStreet Smart Transmission
4L60E / 4L65E2100
4L80E2256
6L80 / 6L902559

What are the DTC codes related to GMC Sierra 1500 transmission problems?

Trouble CodeDescription
P0706Transmission Range Sensor Circuit Range/Performance
P0711Transmission Fluid Temperature Sensor Circuit Range/Performance
P0712Transmission Fluid Temperature Sensor Circuit Low Input
P0713Transmission Fluid Temperature Sensor Circuit High Input
P0714Transmission Fluid Temperature Sensor Circuit Intermittent P0715
P0715Input/Turbine Speed Sensor Circuit
P0716Input/Turbine Speed Sensor Circuit Range/Performance 
P0717Input/Turbine Speed Sensor Circuit No Signal
P0718Input/Turbine Speed Sensor Circuit Intermittent
P0719Torque Converter/Brake Switch B Circuit Low
P0720Output Speed Sensor Circuit
P0721Output Speed Sensor Circuit Range/Performance
P0723Output Speed Sensor Circuit Intermittent
P0724 Torque Converter/Brake Switch B Circuit High
P0740Torque Converter Clutch Circuit Malfunction
P0741Torque Converter Clutch Circuit
P0742Torque Converter Clutch Circuit Stuck On
P0748Pressure Control Solenoid 'A' Electrical
P0751Shift Solenoid 'A' Performance or Stuck Off
P0752Shift Solenoid 'A' Stuck On
P0753Shift Solenoid 'A' Electrical
P0756Shift Solenoid 'B' Performance or Stuck Off
P0757Shift Solenoid 'B' Stuck On
P0758Shift Solenoid 'B' Electrical
P0776Pressure Control Solenoid 'B' Performance or Stuck Off
P0777Pressure Control Solenoid 'B' Stuck On
P0785Shift/Timing Solenoid
P0796Pressure Control Solenoid 'C' Performance or Stuck off
P0894Transmission Component Slipping
P0965Pressure Control Solenoid “B” Control Circuit Range/Performance
P0966Pressure Control Solenoid “B” Control Circuit Low
P0967Pressure Control Solenoid “B” Control Circuit High
P1860TCC PWM Solenoid Circuit Electrical
P1870Transmission Component Slipping: GM Transmission
P2715Pressure Control Solenoid ‘D’ Stuck On

GMC Sierra 1500 Transmission Recalls

Recall 14V152000 – Transmission cooler line leak – 6L80 Transmission
2014 Chevrolet Silverado 1500 Light Duty Regular Cab, Double Cab, and Crew Cab
2015 Chevrolet Suburban
2015 Chevrolet Tahoe
2014 GMC Sierra 1500 Regular Cab, Double Cab, and Crew Cab 2015 Chevrolet Yukon
2015 Chevrolet Yukon XL

Summary –
In March 2014, General Motors recalled certain 2014 Chevrolet Silverado Light Duty Regular Cab, Double Cab, and Crew Cab 1500 series and model year 2015 Suburban and Tahoe; GMC model year 2014 Sierra Regular Cab, Double Cab, and Crew Cab 1500 Series and model year 2015 Yukon and Yukon XL vehicles equipped with a 6L80 6-Speed Automatic Transmission. The recalled trucks may have a transmission oil cooler line that is not securely seated in the fitting.

Consequence –
If the line is not securely seated and transmission oil leaks from the fitting, the oil could contact a hot surface and cause a vehicle fire.

Remedy –
Dealers were instructed to inspect the transmission oil cooler line connection and repair the vehicles, as needed, free of charge. Owners may contact GMC at 1-800-462-8782 (refer to recall 14121) or the National Highway Traffic Safety Administration at 1-888-327-4236 (refer to recall 14V152000).

GMC Sierra 1500 Technical Service Bulletins (TSB)

TSB 05-07-30-017B – Water contamination – 2004-2006 GMC Sierra 1500 4L60E
Problem – A common transmission problem occurs when the transmission shudders/shakes between 40 and 50 mph, as the torque convertor clutch engages. This is caused by rain water getting into the transmission through the dipstick.
Solution – The air inlet grille panel will have to be modified according to the procedure outlined in the TSB.

TSB PIP4051C – Harsh Shifting – GMC Sierra 1500 4L60E
Problem – Unusually harsh gear changes, combined with a P0717 DTC for an input shaft speed sensor error, are often caused by damage to the ISS sensor wiring.
Solution – If wire damage is found (usually to the white wire), the wiring and sensor will have to be replaced. The pump cover should also be examined for sharp points/edges that could damage the wiring. If any are found, they should be smoothed with a file.

TSB 01-07-30-002C – Transmission stuck in third gear with inoperable instrument cluster and multiple DTC’s – 4L60E Transmission & 4L65 Transmission
1999 – 2003 Cadillac Escalade – 2002 – 2003 Cadillac Escalade EXT – 2003 Cadillac Escalade ESV – 1997 – 2003 Chevrolet Silverado – 1997 – 2003 Chevrolet Suburban – 1997 – 2003 Chevrolet Tahoe – 1997 – 2003 Chevrolet Blazer – 1997 – 2003 Chevrolet Express – 1997 – 2003 Chevrolet S10 – 2002 – 2003 Chevrolet Avalanche – 2002 – 2003 Chevrolet Trailblazer – 2002 – 2003 Chevrolet Trailblazer EXT – 1997 – 2003 GMC Sierra – 1997 – 1999 GMC Suburban – 1999 – 2003 GMC Yukon XL – 1997 – 2003 GMC Yukon – 1997 – 2001 GMC Jimmy – 1997 – 2003 GMC Savanna – 1997 – 2003 GMC Sonoma – 2002 – 2003 GMC Envoy – 2002 – 2003 GMC Envoy XL – 1997 – 2003 Oldsmobile Bravada
Problem – Vehicles equipped with the 4L60E and 4L65E transmission may become stuck in third gear, the instrument cluster may not function, and the following DTC’s may be set: P0740, P0753, P0758, P0785 and P1860.
Solution – The most likely cause of this transmission problem is a blown fuse or an open on circuit 1020 between the fuse panel and the transmission. If no battery voltage is found at the fuse, the ignition switch will need to be replaced

TSB 01-07-30-023B – Harsh 1-2 upshift with P1870 DTC – 4L60E Transmission RPO M30
1996 Buick Roadmaster – 1996 Cadillac Fleetwood – 1999-2000 Cadillac Escalade – 1996-2000 Chevrolet Camaro – 1996-2000 Corvette – 1996-2000 Pontiac Firebird – 1996-2000 Chevrolet and GMC Light Duty Truck Models – 1996-2000 Oldsmobile Bravada
Problem – Drivers may experience an unusually harsh 1-2 shift because the ECU has commanded maximum line pressure in order to compensate for excessive wear in the bore that contains the TCC isolator and regulator valves inside of the valve body.
Solution – Replace the 4L60E valve body with revised TCC regulator and isolator valves.

TSB 08-07-30-027 – No movements when transmission is shifted into Drive or third – 4L60E Transmission – 4L65E Transmission – 4L70E Transmission
1982-2005 GM Passenger Cars and Light Duty Trucks: 2006-2007 Buick Rainier – 2006 Cadillac Escalade, Escalade ESV & Escalade EXT – 2006 Chevrolet SSR – 2006-2008 Chevrolet Avalanche – 2006-2008 Chevrolet Colorado – 2006-2008 Chevrolet Express – 2006-2008 Chevrolet Silverado Classic – 2006-2008 Chevrolet Silverado – 2006-2008 Chevrolet Suburban – 2006-2008 Chevrolet Tahoe – 2006-2008 Chevrolet TrailBlazer – 2006 GMC Yukon Denali – 2006 GMC Yukon Denali XL – 2006-2008 GMC Canyon – 2006-2008 GMC Envoy – 2006-2008 GMC Savana – 2006-2008 GMC Sierra Classic – 2006-2008 GMC Sierra – 2006-2008 GMC Yukon – 2006-2008 GMC Yukon XL – 2006 Pontiac GTO – 2006-2007 HUMMER H2 – 2006-2008 HUMMER H3 – 2006-2008 Saab 9-7X – with the 4L60, 4L60E, 4L65E or 4L70E Automatic Transmission (RPOs MD8, M30, M32, M33 or M70)
Problem – It is possible to experience no movement when the transmission is shifted into Drive or the 3rd gear position. It is possible to experience normal operation when the transmission shifted into second, first or reverse.
Solution – Replace the forward sprag assembly

TSB 00-07-30-022D – No reverse, second or fourth gears – 4L60E Transmission & 4L65E Transmission
1993 – 2005 GM passenger cars and light duty trucks
Problem – Drivers may experience the loss of reverse, second and fourth gears. First and third gears will seem to function normally
Solution – The reaction sun gear may fail inside of the sun shell. It will need to be replaced with a stronger heat-treated 4L60E / 4L65 sun gear.

TSB 01-04-17-004B – Clunk, bump or squawk when vehicle comes to a stop, or when it is accelerating from a complete stop – 4WD/AWD vehicles with a one-piece propeller/drive shaft only
1999-2004 Cadillac Escalade, Escalade EXT, Escalade ESV – 1996-1999 Chevrolet 1500 Series Extended Cab Short Box Pickup (Old Style) – 1996-1999 Chevrolet 1500 Series Regular Cab Pickup and Utility Models (Old Style) – 1999-2002 Chevrolet Silverado Extended Cab Short Box (New Style) – 1999-2004 Chevrolet Silverado 1500 Series Regular Cab (New Style) – 2000-2004 Chevrolet 1500 Series Avalanche, Suburban and Tahoe – 2001-2004 Chevrolet Silverado 2500/3500 Series Regular Cab with Long Bed or Extended Cab (New Style) – 2001-2004 Chevrolet Silverado 2500 series crew cab, short box (New style) – 1996-1999 GMC 1500 series extended cab short box (Old style) – 1996-1999 GMC 1500 series regular cab pickup and utility models (Old Style) – 1999-2002 GMC Sierra extended cab short box (New style) – 1999-2004 GMC 1500 series Yukon, Yukon XL – 2000-2004 GMC Sierra 2500/3500 series regular cab with long bed or extended cab (New style) – 2001-2004 GMC Sierra 2500 Series Crew Cab, Short Box (New Style) – 2003-2005 HUMMER H2
Problem – In vehicles equipped with 4WD or AWD, drivers may experience a clunk, bump or squawk noise when they come to a stop, or when accelerating from a complete stop. This may occur during the 2-3 upshift or 3-2 downshift.
Solution – Replace the rear driveshaft slip yoke with a more robust nickel plated slip yoke.

TSB 06-07-30-007A – Harsh 1-2 shift with P0894 DTC – 4L60E Transmission | 4L65 Transmission | 4L70E Transmission
2006 Cadillac Escalade Models – 2006 Chevrolet Light Duty Trucks – 2006 Chevrolet Express Vans – 2006 GMC Light Duty Trucks – 2006 GMC Savana Vans – 2006 Pontiac GTO – 2006 HUMMER H2, H3 – 2006 Saab 9-7X – with 4L60-E / 4L65-E / 4L70-E (RPOs M30, M32, M70) Automatic Transmission
Problem – Drivers may experience an unusually harsh 1-2 shift with a P0894 DTC
Solution – Replace the TCC enable solenoid and/or wiring harness

TSB 08-07-30-008B – Diagnostic information for P0894 and P1870 DTC – 4L60E Transmission | 4L65 Transmission | 4L70E Transmission
2003-2007 GM Passenger Cars and Light Duty Trucks – 2003-2007 HUMMER H2 – 2006-2007 HUMMER H3 – 2005-2007 Saab 9-7X – with 4L60-E, 4L65-E or 4L70-E Automatic Transmission (RPOs M30, M32 or M70)
Problem – This relates to drivers who experience unusually harsh 1-2 shifts, along with a P0804 and/or a P1870 DTC.
Solution – It is possible that a leaking TCC solenoid, a torque converter clutch valve or damaged turbine shaft O-ring seal could cause these two diagnostic trouble codes. However, it could also be caused by a failed torque converter.

TSB 04-07-30-028A – Transmission fluid leak from reverse servo cover – 4L65E
Problem – An ATF leak can occur under the vehicle during cold weather (temperature below 20°F/6.7°C), due to a failed reverse servo cover seal.
Solution – To remedy the problem, an upgraded (see: better quality) reverse servo cover seal will have to be installed.

TSB 08-07-30-016 – Slipping, refusal to shift, overheating GMC Sierra 1500 4L80E
Problem – Slipping between the gears, overheating, refusal to shift out of a gear, and/or DTC P0894 or P0218, may be because by friction material debonding from the torque convertor clutch (TCC).
Solution – If the friction material has circulated throughout the transmission, the entire transmission may need to be replaced. It is possible to remove the material from the internal components (like transmission cooler lines and the valve body), but it depends on the extent of the damage.

TSB 08-07-30-001 – 2001-2006 GMC Sierra 4L80E
Problem – Harsh or delayed shifts, slipping, no forward/reverse gears. Possible DTCs: P0741, P0742, P0751, P0752, P0756, P0757, P0894.
Solution – Rebuild or replace the valve body.

TSB 08-07-30-015 – 2002-2007 GMC Sierra 4L80E
Problem – Harsh shifts, delayed 2-3 shifts, 2-3 shift flare, no 3rd gear, slips in 3rd gear or reverse. Possible DTC 0757.
Solution – If none of the issues described in Bulletin 08-07-30-001 are present (debris in #11 checkball, leak in oil circuit, damage to the direct clutch), then replace the 2-3 shift solenoid due to a possible sticking pintle.

TSB PI488C – No forward or reverse and/or slipping – 6L80 Transmission | 6L90 Transmission
2010 – 2014 Cadillac CTS-V – 2010 – 2014 Cadillac Escalade (all models) – 2010 – 2013 Chevrolet Avalanche – 2010 – 2014 Chevrolet Camaro – 2010 – 2014 Chevrolet Corvette – 2010 – 2014 Chevrolet Express – 2010 – 2014 Chevrolet Silverado – 2010 – 2014 Chevrolet Suburban – 2010 – 2014 Chevrolet Tahoe – 2011 – 2014 Chevrolet Caprice PPV – 2014 Chevrolet SS – 2010 – 2014 GMC Savana – 2010 – 2014 GMC Sierra – 2010 – 2014 GMC Yukon – 2010 – 2014 GMC Yukon XL – 2010 – 2014 GMC Yukon Denali
Problem – Trucks equipped with the 6-speed 6L80 or 6L90 transmission may experience no forward or reverse engagement, or slipping between the gears.
Solution – This problem could be caused by a cracked or split transmission filter. If this is the case, the transmission pump should be disassembled and inspected for possible damage. Inspect for any of the following conditions: – scored pump rotor or pump vanes – scored pump cover or pump rotor pocket – cracked pump slide.

The transmission should also be evaluated for any possible distress to the clutches. GM’s testing and analysis found that split or damaged filters may be caused by a damaged transmission pump. This can send a high pressure fluid spike down the filter neck on a cold start, resulting in the filter body cracking or the filter seam splitting. The filter is not defective and this is not a filter quality issue. Important: Do not replace the filter without inspecting the pump. Failure to inspect the pump and clutches could lead to a repeat of this condition.

TSB 09-07-30-004J – Slips in Reverse or Third, Delayed Reverse or Drive Engagement, DTC P0776, P2715, P2723, Harsh 2-3 Shifts – 6L80 Transmission | 6L90 Transmission
2006-2009 Cadillac STS-V – 2006-2009 Cadillac XLR – 2006-2009 Cadillac XLR-V – 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT – 2006-2009 Chevrolet Corvette – 2007-2008 Chevrolet Silverado – 2008 Chevrolet Suburban – 2007-2008 GMC Sierra – 2007-2008 GMC Sierra Denali – 2007-2008 GMC Yukon Denali – 2007-2008 GMC Yukon XL Denali – 2008 GMC Yukon XL – 2008-2009 HUMMER H2 – 2008-2009 Pontiac G8
Problem – Vehicles equipped with the 6L80 or 6L90 transmission may slip when Reverse is selected or have no/delayed reverse engagement, harsh shifts from 2-3 / 4-5 or slips while in fifth, and slipping acceleration when passing. Possible DTCs include P0776, P2715 or P2723.
Solution – This transmission problem may be caused by a cracked 1-2-3-4 / 3-5-R clutch housing.

Common Problems with the GMC Sierra 1500 Transmission

Intermittent harsh shifting – GMC Sierra 1500 4L60E
Problem – A common Chevy Silverado transmission problem is an intermittent hard 1-2 shift, often accompanied by engine bogging. This condition can be caused by the torque convertor clutch applying during the shift.
Solution – To remedy the problem, the wiring harness needs to be inspected from the transmission case connector to the rear of the engine on the driver side. It’s possible that the wires for the TCC solenoid and pressure control solenoid have become frayed on a body seam. If this is the case, the wiring will need to be repaired, and the harness repositioned.

Solenoid DTC’s – GMC Sierra 1500 6L80E
Problem – A number of diagnostic trouble codes, including P0776, P0796, P2714 and P2723, can be caused by a pressure leak at the end of the clutch regulating valve.
Solution – The bore plug will have to be replaced with updated versions, or modified to accept an O-ring kit.

Lack of Response
Leaking Fluid
Low Fluid
Burning Smell
Grinding or Shaking
Whining, Clunking or Humming
Refuses to Go Into Gear
Torque Converter Issues
Valve Body Issues
Transmission Noisy in Neutral
Gears Slipping
No 3rd or 4th Gear
No 1st or 2nd Gear
No Reverse
Dragging Clutch
Trouble Codes / Check Engine Light

Can I drive with a transmission problem?

If your GMC Sierra 1500 can still make it up and down the road, you might say “It’s fine, I’ll just drive it until I can get it fixed”. But that is not always a good idea, depending on the symptoms. You see, there are a lot of (very expensive) moving parts inside of a transmission, and if something isn’t right, continuing to drive with a transmission problem could damage something else.

How often does a GMC Sierra 1500 transmission need to be replaced?

The overall lifespan of a GMC Sierra 1500 transmission largely depends on how well it was maintained. Factory design flaws also factor into this equation, along with how/how hard you drive. But on average, we’ve seen the GMC Sierra 1500 transmission last for between 130,000-180,000 miles. A high quality replacement transmission however, can last considerably longer if all of the factory design flaws have been addressed and the vehicle has been maintained.

How are GMC Sierra 1500 transmission issues diagnosed?

It is fairly easy to guesstimate what the root cause of your GMC Sierra 1500 transmission problems might be, but you won’t truly know unless you have the right tools and experience. A good mechanic or transmission repair center will be able to connect your truck to a computer and find out which diagnostic trouble codes (DTC’s) have been stored. Once they know what to look for, they can perform a visual inspection to verify the problem.

How is a GMC Sierra 1500 transmission replaced?

In order to replace your GMC Sierra 1500 transmission, the truck has to be lifted from the ground in order to gain access to all of the parts that will need to be unbolted. Then the transmission can be lowered to the ground (typically with a transmission jack), so the new transmission can be installed. Once it is in place, for the 6L80, the vehicle PCM will have to be reprogrammed / reflashed to accept the new transmission using the latest GM subscription.

Recommendations for GMC Sierra 1500 transmission issues?

To save time and get back on the road faster, have your 17-digit truck VIN# handy and you can get an online quote for a reman GMC Sierra 1500 transmission here, then find a local shop using our Find a Shop guide to install it for you.

How to Solve GMC Sierra 1500 Transmission Problems

Solution A: Buy a Used GMC Sierra 1500 Transmission

The quickest way to fix your transmission problems is to simply buy a used transmission or used transmission. These can be found at most junk yards, and they often come with a 30-90 day warranty. However, there’s no way to determine the actual condition of the internal components, so you could be spending a bunch of money to have the exact same problems. Plus, that warranty only covers the transmission if it’s defective, not the labor costs that you’ll have to pay.

Solution B: Buy a Rebuilt GMC Sierra 1500 Transmission

Another option would be a rebuilt transmission or rebuilt transmission. A local repair shop will remove your transmission, then install a bunch of new parts during the rebuild. The problem here is, the skills and experience of each transmission rebuilder will vary widely from shop to shop, so you could have problems from something that wasn’t adjusted properly. And the 1-2 year warranty might only cover you at certain transmission repair shops, in a specific geographical area.

Solution C: Buy a Remanufactured GMC Sierra 1500 Transmission

Many owners depend on their vehicle to commute and get things done. Their gasoline engines are designed to go 100’s of thousands of miles, so it makes sense to invest in a remanufactured transmission.

Need a replacement transmission? Get an estimate for replacement transmissions and local installation. Look up your transmission model by vehicle make and model.

What Transmission Do I Have?

What Problem Does Your GMC Sierra 1500 Have?

Let us know the year, mileage and problem you’re having as well as any trouble (OBD) codes you’ve found. If you’ve been given a quote or paid for a repair, we’d like to hear about that too!

Subscribe
Notify of
Your Name
Email Not Required
93 Tell us about your transmission problems
Inline Feedbacks
View all comments
Tyler Hawn
2 years ago

It won’t go in drive or reverse

Last edited 2 years ago by Tyler Hawn
Donald Lord
2 years ago

I have a 96 GMC Sierra SL tool drive truck I was going down the freeway in cruise control at 60 MPH when all the sudden my RPMs are going up my speed went down I pulled over put it in park a bunch of fluid dumped out and I want to put it in gear and I had nothing I had one quart or I told it to a parking lot I put one quart of oil or transmission fluid in it and it said it was full and I put it I start up put in gear and drove it home and now my transmission fluid looks like chocolate milk what the hell is wrong with it

Penny
2 years ago

No codes given

Penny
2 years ago

I have a 94 GMC SERRIA it has 2023779 miles on it. Just spent close to 1000 dollars getting a new ratatouille alternater new batteries and replaced the heater core quick connector..now i seem to be hearing a funny sound that’s hard to explaine . What could be wrong with it now.

glen
2 years ago

Trans works and shifts, however eventually it acts up / loses reverseand starts making noise.

Cody Coffman
2 years ago

I have a 2014 GMC Sierra vin # 3GT
P1VEC1EG294331and it has the shudder to it or Chevy shake it has 113000 miles is it covered on any recalls or I heard Gmail had came up with a togram for trans has anyone had there’s programmed r recalled looking for what to do now

Penny
2 years ago

I have a 1994 GMC Sierra runs great except for will not go from drive to overdrive seems it just stays put no change in the gears what could be the problem

Christina
2 years ago

Rpm’s spike and doesn’t go anywhere and leaking fluid

JESSIE S YARBOROUGH
2 years ago

Same as all the rest. Took it to the service department. Transmission failure T converter gone.
My thing is if GMC knew of these problems why didn’t they correct them in the future models. I have 4GM vehicles. I don’t think I will buy another one. I have a truck with 66000 .miles with a BD transmission and can’t drive it. I doesn’t stop the payments. I’m very disappointed in GM now.

Anonymous
2 years ago

I have a 2010 GMC sierra SLE I purchased it with the 6L 80 transmission a year ago with 110,000 miles on it it now has close to 150,000 but not long ago I replaced the torque converter because it was slipping between five and six and not downshifting right and knowing that do you know them problems with the torque converter in the vehicle I went ahead and changed it before it let me down. Then about Three months later it all of the sudden gave me a you one oh one last communication with TCM. He came and stayed on for half a day once it cooled off I couldn’t get back up and it went away. Then about two days later it came on again after letting it idle for about five minutes when I was going to work one morning. After that it was pulling up to a stop sign and I shifted it into neutral because I was in lit mode obviously it when it illuminated and it went away as I left a stop sign and shifted. Now it is back on and won’t go away. I got an estimate for the torque converter replacement from AAMCO transmission in my town of Hattiesburg Mississippi for $5000 to replace the torque converter. They said it would be 3500 to replace the torque converter but if they had to go in the transmission it was gonna cost a full five grand. Which is outstandingly obscene (so about an GM remanufactured torque converter for $372 and replaced it myself but of course the fluid cost $100 with the filter for the swap btw). But now I don’t know what to do with this whole TCM programming re-programming global A architecture and all this stuff it’s driving me mad With the service stabili track and all that going off. It’s just hard for me to grasp why it came on and went away and came on and went away at random times if it was a TCM failure I don’t understand myself. wish I kne!!!.

Last edited 2 years ago by Anonymous
star rodgers
2 years ago

I swapped my 4l80e for a 4l60e now it doesnt catch any of the gears..I thought i converted everything over correctly

Anonymous
2 years ago

Will not shift out of first gear unless you let off the gas

Randy
2 years ago

Put a new tranny in 2003 GMC Sierra ran great for a day next morning it wouldn’t come out of 1st

Randy
2 years ago

Put a new training it drove fine for a whole day started this morning won’t shift out of first

Moose.o
2 years ago

2011 gmc sierra 5.3 6speed 4×4 ext.cab.wont shift out of 1st gear auto or won’t go into manual to shift either.why?

David
3 years ago

Silverado 1500 2012 4.8 liter harsh shifting from 1st to 2nd transmission shop installed a new celinoid twice less than 2 months later it’s hard shifting from 1st to 2nd again

Travis
3 years ago

Rpm stays up with hard shift

Frank Hollier
3 years ago

Has a shake when under load when warmed up also hesitate when placing in drive

Zane
3 years ago

Transmission engages in gear you feel it but is stuck in park at the same time even when in nutral the truck couldn’t be pushed i had to remove drive shaft to push truck all the linkage is in working order and engages every gear but won’t move feels like the breaks are on give it gas when in gear and it feels like it’s under load and just don’t move. It’s stuck in park at same time as going in gear

Anonymous
2 years ago
Reply to  Zane

We

Rebecca Washia
3 years ago

I have a 2005 GMC Sierra 1500 2wd, the first problem was the alternator went out. Replaced the alternator then it started overheating. My dad had to rewire the fans because someone had wired the fans to the stereo and that was all fixed. The truck will start and you can drive it but it will not go past 35-40mph. Was told it’s in limp mode. I don’t know. What can you suggest or tell me about what’s going on with it?

Anonymous
3 years ago

Got transmision rebuilt put sensors new alternador still transmission get hot and when put on drive the first gear kicks wat could be my problem

93
0
Would love your thoughts, please comment.x
()
x